Today I'm going to be showing you how to repair
a leaking high-rise faucet. It's showing it's leaking at the neck here. See all the water
coming out? That's not right. It's going to be leaking down below, and we don't want that.
Anyway, for this repair, we don't need to turn the water off.
If you have a single handle
faucet, for that type of repair you would need to turn the water off. A lot of times,
this one you can do by hand, this one here. Just turn it out. If you did need to use a pair of channel locks,
you're going to want to protect your jaws with tape like so, to prevent marring the
You also could use a strap wrench for this, which is a lot better than channel
locks. Because channel locks could deform the neck if you were to squeeze it too tight,
it could deform or reshape the neck as well as mark it up. But a strap wrench kind of grabs it, tightens
down and you can cinch it down and turn it out. But anyway, this one we can do by hand.
Inside here, there's three O-rings, and these are the O-rings that we're going to need to
Now I already know my sizes of O-rings that I need, but if you don't know
what sizes you need, they do sell an O-ring kit. The stuff that I'm going to be using
is pretty stinky. It's this faucet grease here, and if you get
it on your hands, it's pretty tough to wash off. Because it's a high temperature faucet
grease and it's meant to not wash off with water.
When you go to repair this, you're
going to want to wear gloves, and a good way to do this is to wear two or three pairs of
these disposable gloves. You'll see reason I do this is this stuff's
so smelly. What you can do is unwrap the glove, one of the gloves, in order to use your tools
and not get the faucet grease all over your tool. Not get the faucet grease all over the
outside of the faucet.
This faucet is going to be in need of some cleaning afterwards
anyway, but that's another story. The easy way to get these O-rings off is to
use a small flathead screwdriver. I've got one in my Leatherman, so it comes in handy
for this. And it's just a matter of picking these off, fairly simple.
If you keep them
together, you can use that to size up your new O-ring to make sure you're getting the
right size. And all three of these are the same size, so you really only need to keep
one together so if you needed to cut it, you could. Not a big deal. Okay.
One, two, three O-rings,
another reason for the gloves there. Now what you want to do is coat this so that underneath
it, it'll have a coating of the faucet grease. This stuff can be a little tricky to get apart
sometimes, and mine's getting kind of old. It's time to order some more faucet grease.
So anyway, go underneath where your O-rings are going to go.
Okay. Now we'll slip our
new O-rings on. Here's the first one. Yeah, the gloves are going to make it a little tricky,
but it's what it is, job security.
There's the second one, and number three.
Now we're going to coat the outside of the O-rings with the faucet grease. This is a
high temperature faucet grease, so it's not going to come off with hot water, and lubing
this all around is going to prevent our O-rings from pinching up inside there. Because if they pinch then they're going to
break, and then your faucet's going to leak. Okay, now that we got that, this is the good
time to go ahead and remove that outer layer of the gloves.
We can dispose of those. Now
we're ready to put our faucet neck back together. So we can slip this up, and then push it in
all the way around gently, and then go ahead and slowly hand thread this in place so that
we don't get it cross-threaded. We can get rid of these, and we're just going to hand
tighten this down.
Once that's nice and tight…And now once that's nice and tight, just hand
tightened, we're going to prove it and check for any leaks. Now if we see any leaks here, then can use
our channel locks to tighten it up a little bit more, but it looks like everything's good
here, no leaks. So now you want to check underneath for any
leaks, and you'll need to remove your gloves to do that. I'm going to take these off now
and check for any leaks down below.
Now first, you want to take your rag, dry everything
off. It looks like we've got a loose handle there also. I'll show you how to tighten that
up, it's just an Allen wrench under here, it's real easy, but that's another story.
I may put out another video how to tighten those down. I can try to put the link on the
Going to come down below the sink and feel
all around for any leaks. Now, you may have to dry everything off and check this the following
day, as it was leaking before. So you probably have some water that's still trapped inside
there, so you're going to have to just keep an eye on this, and do what you can to dry
it out. Then go ahead and turn the water on.
see a flood of water, you know you've got a problem you've got to deal with. But if
you're just feeling a little bit of moisture from before, you're actually okay. An old trick is after you dry everything up
below, is to put paper towels down, or toilet paper in order to check it. Wow, there's something
wrong here, someone skipped the air gap, that's not good for the dishwasher.
You don't want
to do that. Skipping that air gap can make you really
sick, because the air gap prevents the sewer gases from going into your food when it passes
from your disposer, so you definitely don't want to run it straight in like this. This is wrong. So if you see this, you definitely
want to install an air gap to prevent getting harmful bacteria and everything into your
Anyway, that's another story also. Anyway, if we have no leaks here we're all
set, good to go. One fixed high-rise kitchen faucet. Good to go..